How to install screen replacement for iPad 3?

On April 1, 1976 Apple founded. Since Steve Jobs built Apple this high-tech brand company, every time it issued new products, it will cause so numerous consumers crazy. Its new product Apple iPad 3 rear camera has five million Pixels, its battery is used to polymerize physical properties, standby time for a long time, and even the fuselage can also store 16GB performance, the resolution is very clear. When the Apple's screen was destroyed, we no longer watch or normal use it no matter how good to storage and standby. Next Chris Cui from Cell Phone Age com shares you some tips for iPad 3 screen replacing.

How to do when the iPad 3 screen broken?

First try to boot, to check if the inner screen is damaged. From Internet you can see a lot of screen replacing tips, but all are very simple, not introduced in great detail. If you not very trust in your own ability, to find a professional repair shop will be more secure. But if you want to save money and decide to personally try it yourself (if not success, then take out the money for the screen), you’d better refer to this article that describes how to replace a screen in detail. iPad assembly manufacturer is in Chengdu, iPhone assembly factory is in Guangdong, first to buy a new screen either from online shop or Apple parts store in Huaqiang North, Shenzhen.

Specific steps:

1. First prepared tools: hair dryer (preferably professional hot air gun), gas blowing, cross flower screwdriver (trumpet suit the best), lens pen, crowbar (stainless steel, professional repair phone appliances, as plastic basic hardness is not enough) 3M double-sided adhesive, etc., every function in the following will be known.

2. Hair dryer open to the largest heat level, we must remember that the glass ballast on table should be clean up before blow, otherwise it will be blew everywhere. Blowing the edge of iPad 3 (white side), first pry where to blow where, Otherwise, the place where be blown will cool. Blow while prying. Black is iPad 3 original 3M glue.

3. This is the focus of iPad 3, one is the HOME key, and one is the WIFI module. If pry broken, WIFI module will spend 50 USD, HOME as 30 USD, so the local destruction of the method is still useful. We see a circle of silver in iPad. That is the plastic side of the tank, do not destroy it as from Internet some people pry broken, and spent a seemingly more than 100 USD. Outside screen is installed inside, to prevent dust from entering. We have to remember these two positions, be careful pry, do not increase the screen budget for you. HOME key is active, you can put it down. On the screen glass ball, find a paper on top to not pollute the environment.

4. Finally put the outer screen pry down, gently turned on the left, because the bottom is still connected to the iPad, below the middle there is cable. Now yet can’t take off outer screen, because the cable connected to the motherboard. Here are the red circle, look at the four red circle, which is the screen screws, very simple, with a cross screwdriver to take off (preferably with a magnet). They are very small so find a place to put up, do not lose. Look at the right side of the red circle, which is outside the screen and the LCD screen on the back of a circle of flash, play a role of fixing and dust-proof.

5. Remove the four screws of the LCD screen to see the original code of the LCD screen. Outside the screen of the cable, pay attention to a bayonet, with a small screwdriver to pry; LCD bayonet, with the same operation; outside the screen of the cable is also operated as previous, you can take it down. Gently take off the LCD bayonet, and then take the outer screen bayonet, so as to remove the overall external screen.

6. Began to clean up the glass pieces inside, with the prepared air blowing, carefully cleaned up. And then the surrounding with anhydrous alcohol to clean the residual double-sided adhesive, increase the adhesion. Put the gift 3M double-sided plastic on, remember that all places should be 3M glue. And then follow the above method to carry out, the LCD screen and the external screen can be installed and then use the lens pen to clean the fingerprints on the LCD screen. Do not forget the four screws on the LCD screen and the two bayonets located well.

After learning from Apple iPad 3 screen replacing do not blindly change the screen. The above details of the operation are essential. We first have to know iPad 3 operating system is the famous iOS, while iPad 3 processor is naturally extraordinary. We are in the process of changing the screen, if the slightest effect may destroy the internal function of iPad 3. So it is best to find someone to counseling. Of course, an Apple iPad 3 original screen is very expensive, meanwhile on market there are a lot of fake items. For users it is suggested to buy iPad 3 touch screen replacement from professional mobile phone parts sellers such as Cell Phone Age com.